Advanced Search
Search Results
671 total results found
DS118W
The Yamaha DS118W is an 18-inch powered subwoofer that is usually used on smaller events and DJ rigs.
DXR8
The Yamaha DXR8 is a powered point-source speaker with an 8-inch speaker typically used for background music in Pre-function areas and sometimes as room delays.
Behringer B112MP3
The Behringer B112MP3 is a powered speaker used for delays and small events where money is a heavy concern.
Behringer B212
The Behringer B212 is a powered speaker used for delays and small events where money is a heavy concern.
Behringer B412
The Behringer B412 is a powered speaker used for delays and small events where money is a heavy concern.
Behringer iNuke 6000
The Behringer iNuke6000 is a 2 in/2 out amplifier. It can run in dual mono, Stereo, and Bi-amp modes. It outputs 1,800 watts per channel at 8 ohms and 3,100 per channel at 4 ohms.
Crown Macro-Tech 36x12
The Crown Macro-Tech 36x12 is run bi-amped for our active monitors. You can fit a maximum of two monitors per amplifier.
Lab Gruppen PLM's
The Lab Gruppen PLM amp racks contain 3 different models, all of their information can be found here.
Nexo 4x4
Nexo 4x4 amplifiers are used on most of our everyday shows. They can power all of our Nexo speakers and Subs. It is a 4 input and 4 output amplifier. Inputs can either be Analog or Dante. Note: This is the only amplifier that we do both speakers and subs on ...
QSC PLX3402
The QSC PLX3402 is a 2 channel amplifier used for passive monitors. This amplifier is typically used on smaller shows to power our entry-level monitors.
Avid/Digidesign SC48
Behringer X32
Midas M32
Yamaha CL5
Yamaha MG10
Yamaha QL1
Yamaha QL5
ADJ (DMX Operator)
The ADJ DMX operator controls up to 192 DMX channels. The console has one 3-pin DMX output. You can record up to 6 chases and can playback with seperate fade and step speeds. The ADJ has 12 individual fixture buttons which allow for control of up to 12 seperat...
Avolites: Titan I (TI)
Titan I is a complete Avolites set without external components, meaning it is run entirely on PC. It supports one universe of DMX, and supports ArtNet and s-ACN. The software is called Titan Go, and the operating screen is slightly different than normal as it ...
Avolites: Tiger Touch II
The Tiger Touch II is the next level of Titan console, with 4 physical 5-pin DMX outputs, with support for up to 16 ArtNet or s-ACN outputs, which is 8192 channels. Integrated touch screen allows for ease of use and 10 playback faders with 60 pages allows for ...
15' X 73' Projection Details
3:1 Aspect Ratio Test Patterns
3:1 Test Patterns
LED Poster Template
OBSBOT Smart Remote Controller Pairing
Remote Pairing Power on the OBSBOT Tail Air. Press the Tail Air's power button 3 times.(The status indicator will flash light blue) On the remote hold the Human Tracking button and then the number 1, 2, or 3 that you would like to assign that camera t...
Basic Information
Product Page Our Barco UDM-4K22 projectors are large-scale laser projectors, primarily used for larger screens, and when maximum brightness is a necessity. Projectors are sent in a fly cage, with locking pins for stacking. (4) SDI input connectors. The firs...
A.I. Tracking
The OBSBOT can use A.I. Tracking to automatically follow both human and animal subjects.
OBSBOT Smart Remote Controller
This is the simplest method of controlling a Tail Air. Pair your Remote. If you depress the joystick you can control the pan and tilt of the Tail Air using the Remote's Gimbal.
OBSBOT Center(PC App)
OBSBOT Start(iOS App)
Roland Camera Control
All models of Roland would need to be on the same network as the camera in order for these control methods to work. vr-120 HD Menu > Camera Control > Jump to Setup Select which camera you would like to assign it to. Switch the Protocol to VISCA over IP Ch...
vMix PTZ(requires 4k vMix License or higher)
Bitfocus Companion(Sony Visca over I.P.)
A recommendation for ALL control methods
It is ALWAYS recommended to have a laptop that can run OBSBOT Center available as this is the best way to adjust any camera settings that you may need to change during setup. These settings can also be accessed through OBSBOT Start but it is simpler to access...
Basic Information
Product Page Our Barco UDM-4K30 projectors are large-scale laser projectors, primarily used for larger screens, and when maximum brightness is a necessity. Projectors are sent in a fly cage, with locking pins for stacking. (4) SDI input connectors. The firs...
Basic Information
Product Page Our Epson 12K projectors are large-scale laser projectors, primarily used for larger screens, and venues. Projectors are sent in a fly cage, with locking pins for stacking. (1) SDI input, (1) HDMI input. Power cable is an Edison connector, but...
Basic Information
Product Page Our Epson 13K projectors are large-scale laser projectors, primarily used for larger screens, and venues. Projectors are sent in a fly cage, with locking pins for stacking. (1) SDI input with Loop Out, (1) HDMI input. Power cable is an Edison ...
Basic Information
Product Page Our Barco HDX-W20 FLEX projectors are large-scale lamp projectors, primarily used for larger screens, venues, and when maximum brightness is a necessity. Projectors are sent in a fly cage and are fitted with top and bottom feet that interlock fo...
Basic Information
Product Page The Sony RM-IP500 is the controller for our Sony BRC-X400 robo cams. It comes a CAT5 patch cable, and a Netgear PoE+ switch. The controller connects to the PoE+ switch using the LAN port with the CAT5 patch. The cameras are then fed power and co...
Connecting Sony BRC-X400 Robo Cams
Ensure all of your cameras are connected to the PoE+ switch and are receiving power. Using the Select knob, scroll down to "Auto IP Setup" and click knob to enter. Click Knob to enter "Setup IP". Use the Select knob to scroll down to "Setup IP". Use the Val...
Connecting Sony BRC-X400 Robo Cams
Ensure all of your cameras are connected to the PoE+ switch and are receiving power. Using the Select knob, scroll down to "Auto IP Setup" and click knob to enter. Click Knob to enter "Setup IP". Use the Select knob to scroll down to "Setup IP". Use the Val...